Welding 101
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesIntro to Welding.
This is the Basic startup class for using the Mig Welding in the Metal Area.
We will spend 30 minutes on basic safety and area requirements.
Then expect an hour of hands on setup and shared MIG welding time
I’m going to limit the number of students to 5 , so each person get enough hands on time to be able to feel comfortable using the MIG welder
Students should bring their own shield and gloves, if they have them. But they are not required, as we have setups available to use.
Please do NOT bring your own welding equipment to use, the setup and testing time could impact other students.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**
There will be a fee for this class of $9.96 for current Knox Makers members. There will be a maximum of 8 spots for this class, and a minimum of 3 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class will be canceled and all tickets will be refunded.
Project Lathe: Workday
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesCome help clean, tune and get the new 13x40 MSC lathe up and running. We purchased a new to us lathe which requires a little maintenance before it's ready to use. This is a good opportunity to see the insides of a lathe and learn a bit more about them.
August Board Meeting
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesKnox Makers members are welcome to join us as we hold our monthly board meeting. The board will be discussing pertinent topics happening around the space. All current, paying Knox Makers members are welcome to attend. This event is closed to the general public.
Directions- Knox Makers parking and entrance is located around the back of the SPARK building in the fenced in area.
Knox Makers is a place for the Knoxville area’s engineers, artists, hobbyists, innovators, educators and entrepreneurs to work and play. We are a technology and art collective dedicated to the promotion of creativity enabled and informed by science. Our lectures, workshops, and outreach programs inspire and educate both members and the general public. Our workshop provides members with both the space for large projects and the tools to complete them. We are a non-profit educational organization supported by member dues and staffed by volunteers.
Workday: Classroom Wall Framing
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesJoin us for our first classroom work day - framing the wall in. All the supplies are at Knox Makers and strewn about - lets get them in place! This project does not require any previous construction experience, and there will be a wide variety of tasks to take on. Come for part or the entire day - any contribution is appreciated.
Milling 101 – Bridgeport Mill Tool Authorization
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United States** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. *****
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.
There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
August New Member Onboarding
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesKnox Makers will host a member onboarding session for new members. This night will start with a brief overview of the resources, rules, and goals of Knox Makers. Afterwards, members should feel welcome to stay and socialize. The focus of this evening will be on members who are new to Knox Makers, but older members are encouraged to come help and meet newer members. Snacks will be provided, so please RSVP so that we can make sure we provide an appropriate amount.
3D Printing 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesIf you are looking to buy a 3D printer or maybe you want to learn how to use the printers at the Knox Makers, this class will get you started. With the explosion of affordable printers in the market, desktop 3D printing is within many people's budget, but maybe the lack of knowledge is holding you back.
Learn about the basics of 3D printing such as:
The different 3D printing technologies
Finding and selecting models
Selecting the correct materials for the job
Using slicing software
Operating and basic maintenance of a 3D printer
Laser Cutter 101
Knox Makers - Lasercutting 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Goldfinger. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Goldfinger or need/want a review of its operation.
Laptops will be provided for this class.
Help installing the software on your own laptop can be provided outside of class.
In class we will be using Inkscape and the laser cutting extension bundle we’ve put together for it. There is a minimum of one participant and maximum of five participants.
You can find Inkscape at: https://inkscape.org/
You can find the KM-Laser bundle at: https://github.com/KnoxMakers/KM-Laser
Fine Tuning FFF 3D Printers
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesLearn how to melt plastic better by deep diving into some more obscure slicer and firmware settings for FFF printers. This class will be mostly lecture and is intended for attendees that already have a grasp on the fundamentals of 3D printing. You do not need to bring your printer unless really really want to.
Going from Schematics to Breadboards
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesIn this class Ray will lead you step by step through reading a schematic and translating it into a prototype on a solderless breadboard. Each attendee will build a circuit using an integrated circuit, resistors, capacitors and diodes to take home and show off to friends!
September Board Meeting
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesKnox Makers members are welcome to join us as we hold our monthly board meeting. The board will be discussing pertinent topics happening around the space. All current, paying Knox Makers members are welcome to attend. This event is closed to the general public.
Directions- Knox Makers parking and entrance is located around the back of the SPARK building in the fenced in area.
Knox Makers is a place for the Knoxville area’s engineers, artists, hobbyists, innovators, educators and entrepreneurs to work and play. We are a technology and art collective dedicated to the promotion of creativity enabled and informed by science. Our lectures, workshops, and outreach programs inspire and educate both members and the general public. Our workshop provides members with both the space for large projects and the tools to complete them. We are a non-profit educational organization supported by member dues and staffed by volunteers.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**
Laser Cutter 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Goldfinger. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Goldfinger or need/want a review of its operation.
Knife Sharpening 101
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesAn intro to basic knife sharpening .
All you need to bring is a pocket knife, small sheath knife or a kitchen paring knife. (SAVE YOUR RAMBO KNIFE FOR ANOTHER TIME). You should walk away with a basic understanding of sharpening small blades and a sharp knife at the end of this class.
October New Member Onboarding
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesKnox Makers will host a member onboarding session for new members. This night will start with a brief overview of the resources, rules, and goals of Knox Makers. Afterwards, members should feel welcome to stay and socialize. The focus of this evening will be on members who are new to Knox Makers, but older members are encouraged to come help and meet newer members. Snacks will be provided, so please RSVP so that we can make sure we provide an appropriate amount.
October Board Meeting
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesKnox Makers members are welcome to join us as we hold our monthly board meeting. The board will be discussing pertinent topics happening around the space. All current, paying Knox Makers members are welcome to attend. This event is closed to the general public.
Directions- Knox Makers parking and entrance is located around the back of the SPARK building in the fenced in area.
Knox Makers is a place for the Knoxville area’s engineers, artists, hobbyists, innovators, educators and entrepreneurs to work and play. We are a technology and art collective dedicated to the promotion of creativity enabled and informed by science. Our lectures, workshops, and outreach programs inspire and educate both members and the general public. Our workshop provides members with both the space for large projects and the tools to complete them. We are a non-profit educational organization supported by member dues and staffed by volunteers.
Knife Sharpening 101
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesAn intro to basic knife sharpening .
All you need to bring is a pocket knife, small sheath knife or a kitchen paring knife. (SAVE YOUR RAMBO KNIFE FOR ANOTHER TIME). You should walk away with a basic understanding of sharpening small blades and a sharp knife at the end of this class.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**
There will be a fee for this class of $9.96 for current Knox Makers members. There will be a maximum of 8 spots for this class, and a minimum of 3 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class will be canceled and all tickets will be refunded.
Milling 101 – Bridgeport Mill Tool Authorization
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United States** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.
There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.