Laser Cutter 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Moonraker. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Moonraker or need/want a review of its operation.Laptops will be provided for this class.
If you were authorized on Goldfinger, there is no need to take this class. For a review of the new laser, please stop by the shop after this class or on a Tuesday to get a tour of the new machine.
Help installing the software on your own laptop can be provided outside of class.In class we will be using Inkscape and the laser cutting extension bundle we’ve put together for it. There is a minimum of two participant and maximum of five participants.
Mig Welding 101
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesIntro to MIG welding.
This is the Basic startup class for using the MIG Welder in the Metal Shop.
We will spend about 30 minutes on basic safety and area requirements.
Expect an hour or so of hands on setup and shared MIG welding time (more if needed.)
*The class may run a bit short or long depending on students needs. *
Students should bring their own Welding Shield, gloves and other PPE (Personal Protective Equipment) if they have them.. but these are not required. The Metal Shop has all the required equipment for those who don’t have their own.
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Cost of the event is $19.96 and is for Knox Makers members only.
Making a beer can stove
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesMaking a beer can stove. Ultralight backpacking stove that burns alcohol. Any aluminum beverage can will work. You need to have 3 empty cans to make one. There is a…
Creating Wood Inlays
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesBrian will be demonstrating the technique he use for making wood inlays. In this class you will practice this technique and create an inlay of a leaf on a piece of ash stock. You will be using marking knives, routers, gouges, chisels and the bandsaw. All materials and tools will be provided, however if you have your own marking knife or gouges you would prefer to use I encourage you bring them.
Hand Tool Sharpening
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesBrian will be demonstration and how-to's of sharpening hand planes, gouges, chisels and card scrapers. Will also include hands-on setup/use of these tools.
Cost of the event is $14.96 for members and has a maximum of 6 students.
Perfect Miters and Splines
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThe miter is one of the most difficult joinery techniques to execute well. Error in fitment is additive which manifests a "last corner" in a box or picture frame that does not close up. In this class we will demonstrate tips and tricks to making perfect fitting miter joints every time. We will also demonstrate how to safely implement spline reinforcement for added stability and decorative enhancement of the joint. This will involve advanced table saw use, jigs and sleds, layout techniques, shooting board use and an increased state of happiness in ones future work.
This class is limited to 5 students. The cost is $19.96 for Knox Makers members, $39.96 for General Public
Inkscape 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesInkscape is a free and open sourced vector graphics editor. It is the primary software used to interface with Knox Makers’ laser cutter, CNC router, and vinyl cutters. This class will teach basics of drawing and arranging shapes, talk about vectors and paths, and give a general overview of Inkscape and its capabilities.
Computers will be provided, but if you want to use your own, you can download Inkscape at inkscape.org
There is a maximum of 6 participants. The cost for the class is $19.96 for Knox Maker Members and $29.96 for Non-Members.
Inkscape 201: Inkscape for the Laser
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesInkscape is the primary vector graphics editor used at Knox Makers. In this secondary class, some useful extensions and processes common to the laser will be taught, including:
- hatch fill extension
- engraving raster images
- node editing and tracing
- figuring out slots and tabs
Computers will be provided and a basic knowledge of Inkscape is expected of participants. If you wish to bring your own laptop, please download Inkscape at inkscape.org and come a few minutes early to make sure it is set up properly.
There is a maximum of 6 participants. The cost for the class is $19.96 for Knox Maker Members and $29.96 for Non-Members.
Hand Cut Dovetails
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesIn this class you will receive instruction on layout, cutting, and chopping techniques and tools used for constructing hand cut dovetail joinery. The dovetail is the strongest and most utilitarian mechanical corner joint used in woodworking. All tools and materials will be provided for use in this class, however if you have your own dovetail saw, coping/jewelers saw, chisels, scribe or marking knife then feel free to bring your own. By the end of this class you will create one through dovetail joint and one half-blind dovetail joint along with learning some tricks to speed up the process.
This class is limited to 2 students. The cost is $39.96 for Knox Makers members, $69.96 for General Public
Annual Members Meeting
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesThis week we will be having our annual members meeting. We will go over the state of the organization, what we have accomplished in the past year, and what our…
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Cost of the event is $19.96 and is for Knox Makers members only.
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will…
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will…
Intermediate Oscilloscope Use and Understanding
Knox Makers - VirtualNote: This is a virtual event! Have you used an oscilloscope but most of the buttons and features look like hieroglyphs from a foreign land? Do you want to…
Hand Tool Sharpening
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesBrian will be demonstration and how-to's of sharpening hand planes, gouges, chisels and card scrapers. Will also include hands-on setup/use of these tools.
Cost of the event is $14.96 for members and has a maximum of 6 students.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Laser Cutter 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Moonraker. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Moonraker or need/want a review of its operation.Laptops will be provided for this class.
If you were authorized on Goldfinger, there is no need to take this class. For a review of the new laser, please stop by the shop after this class or on a Tuesday to get a tour of the new machine.
Help installing the software on your own laptop can be provided outside of class.In class we will be using Inkscape and the laser cutting extension bundle we’ve put together for it. There is a minimum of two participant and maximum of five participants.
Cutting Torch 101
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis is the Authorization Class to use the oxy-fuel cutting torch.
We will spend some time going over safety and then move on to operation of a cutting torch. We will cut out some basic shapes as well as learn some other tricks you can use a torch for.
Students should wear natural fiber clothing (jeans, cotton shirts, etc) NO polyester, spandex or "tech" style clothes. Socks and shoes are required, NO sandals or open toes.
If you have own PPE- please bring safety glasses, leather gauntlets, shade 5 cutting goggles/glasses, and a welding shirt/jacket. *If you do not have this yourself do not worry! We will have gear for you to use!*