Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to…
Laser Cutter 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Moonraker. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Moonraker or need/want a review of its operation.Laptops will be provided for this class.
If you were authorized on Goldfinger, there is no need to take this class. For a review of the new laser, please stop by the shop after this class or on a Tuesday to get a tour of the new machine.
Help installing the software on your own laptop can be provided outside of class.In class we will be using Inkscape and the laser cutting extension bundle we’ve put together for it. There is a minimum of two participant and maximum of five participants.
Hand Tool Sharpening
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesBrian will be demonstration and how-to's of sharpening hand planes, gouges, chisels and card scrapers. Will also include hands-on setup/use of these tools.
Cost of the event is $14.96 for members and has a maximum of 6 students.
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will receive a key to access the forge and foundry building.
Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is OK but synthetic clothing or other materials that can melt are unsafe. We have eye protection available but suggest you bring your own if you have them.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.
Creating Wood Inlays
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesBrian will be demonstrating the technique he use for making wood inlays. In this class you will practice this technique and create an inlay of a leaf on a piece of ash stock. You will be using marking knives, routers, gouges, chisels and the bandsaw. All materials and tools will be provided, however if you have your own marking knife or gouges you would prefer to use I encourage you bring them.
New Members Onboarding
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesWhether you’re a current member, trial member, or prospective member, you’re welcome to join us at this month’s New Member Onboarding! We’ll start with a brief overview of Knox Makers’…
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Cost of the event is $19.96 and is for Knox Makers members only.
Milling 101 – Bridgeport Mill Tool Authorization
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United States** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.
There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
TIG Welding 201
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesContinue to Weld.
This is the more advanced class for using the TIG Welder and Plasma Cutter in the Metal Area. We will spend just a few minutes on basic safety and area requirements. First we will go over the basic Plasma cutter setup, expect 30 minutes of hands on metal cutting
Then expect the next hour of hands on setup and shared TIG welding time
I’m going to limit the number of students to 5, so each person gets enough hands on time to be able to feel comfortable using the TIG welder and Plasma Cutter
You MUST have completed the Welding 101 or already feel very comfortable MIG welding before taking this class, as it is not an intro to welding, but a more advanced class focusing on TIG
Students should bring their own shield and gloves, if they have them. But they are not required, as we have setups available to use.
Please do NOT bring your own welding equipment to use, the setup and testing time could impact other students.
There will be a fee for this class is $19.96 for current Knox Makers members. There will be a 2 person minimum, maximum of 5. If the class minimum is not reached by midnight two days before the event the class will be canceled and all tickets will be refunded.
Flexo 101 – Intro to Cold Bending
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis is the Basic startup class for using the Hossfeld Standard Model No. 2 Bender
in the Blacksmithing Area.
We will spend 15 minutes on basic safety and area requirements.
Then expect 45 minutes of hands on setup and shared bending time
We will supply some material to bend, but feel free to bring your own material
(I’m not saying you will be able to bend your material, but we will discuss the machine limitations)
I’m going to limit the number of students to 5 , so each person get enough hands on time to be able to feel comfortable using the Hossfeld bender
Students should bring their own gloves
The cost is $19.96 for Knox Makers members
Mig Welding 101
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesIntro to MIG welding.
This is the Basic startup class for using the MIG Welder in the Metal Shop.
We will spend about 30 minutes on basic safety and area requirements.
Expect an hour or so of hands on setup and shared MIG welding time (more if needed.)
*The class may run a bit short or long depending on students needs. *
Students should bring their own Welding Shield, gloves and other PPE (Personal Protective Equipment) if they have them.. but these are not required. The Metal Shop has all the required equipment for those who don’t have their own.
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will receive a key to access the forge and foundry building.
Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is OK but synthetic clothing or other materials that can melt are unsafe. We have eye protection available but suggest you bring your own if you have them.
Cutting Torch 101
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis is the Authorization Class to use the oxy-fuel cutting torch.
We will spend some time going over safety and then move on to operation of a cutting torch. We will cut out some basic shapes as well as learn some other tricks you can use a torch for.
Students should wear natural fiber clothing (jeans, cotton shirts, etc) NO polyester, spandex or "tech" style clothes. Socks and shoes are required, NO sandals or open toes.
If you have own PPE- please bring safety glasses, leather gauntlets, shade 5 cutting goggles/glasses, and a welding shirt/jacket. *If you do not have this yourself do not worry! We will have gear for you to use!*
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Cost of the event is $19.96 and is for Knox Makers members only.
Inkscape 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesInkscape is a free and open sourced vector graphics editor. It is the primary software used to interface with Knox Makers’ laser cutter, CNC router, and vinyl cutters. This class will teach basics of drawing and arranging shapes, talk about vectors and paths, and give a general overview of Inkscape and its capabilities.
Computers will be provided, but if you want to use your own, you can download Inkscape at inkscape.org
There is a maximum of 6 participants. The cost for the class is $19.96 for Knox Maker Members and $29.96 for Non-Members.
Laser Cutter 101
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Moonraker. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been authorized to use Moonraker or need/want a review of its operation.Laptops will be provided for this class.
If you were authorized on Goldfinger, there is no need to take this class. For a review of the new laser, please stop by the shop after this class or on a Tuesday to get a tour of the new machine.
Help installing the software on your own laptop can be provided outside of class.In class we will be using Inkscape and the laser cutting extension bundle we’ve put together for it. There is a minimum of two participant and maximum of five participants.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
Cost of the event is $19.96 and is for Knox Makers members only.
Inkscape for the Laser
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesInkscape is the primary vector graphics editor used at Knox Makers. In this secondary class, some useful extensions and processes common to the laser will be taught, including: - hatch…