Woodworking 202 – Advanced Basics
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesYou MUST have completed Woodworking 102 “Woodturning Basics” prior to taking this class. This class is a continuation of basic woodturning skills beyond spindles and it will include a brief safety reminder. There will be a short discussion regarding the variety of projects that can be accomplished on a wood lathe: utilitarian, decorative and artistic. Turning skills covered in this class will include: resourcing, preserving and preparing wood for turning; options for mounting wood on the lathe; the vast variety of tools, how they are used and sharpened; other materials that can be turned on a wood lathe; sanding and finishing options. Hands-on opportunities will include, but may not be limited to if time permits, starting a hollow form such as a bowl.
Class members are encouraged to bring eye protection (full face shields are ideal. Do not wear any long, loose-fitting clothing, long sleeve shirts, bracelets, rings or low hanging neck chains. A hat would be appropriate if you don’t want to be picking woods chips out of your hair.
Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.
Jewelry Soldering 101
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesIntro to Jewelry Soldering.
This is the Basic startup class for Soldering Jewelry in the Machining Area. We will spend 30 minutes on basic safety and area requirements. Then expect an hour of hands on setup and soldering a copper ring.
I’m going to limit the number of students to 3 , so each person get enough hands on time to be able to feel comfortable soldering with a torch.
No special PPE is required
Please do NOT bring your own jewelry to solder, the time helping you could impact other students.
Milling 101 – Bridgeport Mill Tool Authorization
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United States** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **
This is a hands on class and is subject to run over the allotted 4 hours. Please make sure your schedule is free accordingly.
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.
There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 1 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area, as well as some shop etiquette guidelines. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context of taking rough lumber through the process of milling and operation of all equipment in the space. If you have previously paid and attended a wood authorization class then we encourage you to audit the class free of charge at any time.
The cost is $24.96 for Knox Makers members, $44.96 for General Public. There will be a maximum of 8 spots of this class, and a minimum of 4 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
Open Hack Night – Public Welcome
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesOpen hack nights are a chance for people to come out to Knox Makers and hack on anything at any skill level. You can come out to practice a new programming language, get help working on your personal projects, or try your hand at using the 3d printer. You might just come out to see what other folks are working on and lend a hand. If you know anyone who has been curious to come out to Knox Makers, please invite them along!
Like all other Tuesday nights, this event is free and open to the public. Our night will begin with a Show and Share where attendees are encouraged to bring out the projects they have been working on. This is a great time to request feedback for the future direction of your project, or you can just bring out something you want to show off. We hope to see you there!
New Members Onboarding
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesWhether you’re a current member, trial member, or prospective member, you’re welcome to join us at this month’s New Member Onboarding!
We’ll start with a brief overview of Knox Makers’ origins and purpose and talk about how the organization works. You’ll learn a bit about the resources available to members and about the path to membership. Afterwards, we’ll hang out and socialize.
The focus is on new members, but longer-term members are encouraged to come and meet new folks.
Embroidery Machine Auth
Knox Makers - Fiber Arts 116 Childress St SW, Knoxville, TN, United StatesThis is the authorization class needed to use the Brother Innov-is NQ1700E Embroidery Machine. The general format of the class covers choosing the right stabilizer and needle for your project, hooping, designing and stitching it. A hands-on approach will show the basics of how to turn the preloaded text and images into fabric art.
For the more advanced, loading up a pes file format embroidery design of your own will be covered. Class time will vary depending on number of questions and skill level of participants.
Lock Picking 101 – LockSport
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis Is the Authorization class for the Lockpicks and locksport.
We will go over safety and proper use of lockpicking tools and the ethics behind locksport.
“Locksport is the sport or recreation of defeating locking systems. Its enthusiasts learn a variety of skills including lock picking, lock bumping, and a variety of other skills traditionally known only to locksmiths and other security professionals. Locksport followers enjoy the challenge and excitement of learning to defeat all forms of locks, and often gather together in sport groups to share knowledge, exchange ideas, and participate in a variety of recreational activities and contests.”
Upon completion of this course the Student will understand; the physical mechanics of Hacking a pin tumbler lock, the ethics behind lockpicking, and will successfully pick a five pin lock.
The cost is $44.96 for Knox Makers members, $64.96 for General Public. There will be a maximum of 10 spots of this class, and a minimum of 4 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
Open Hack Night – Public Welcome
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesOpen hack nights are a chance for people to come out to Knox Makers and hack on anything at any skill level. You can come out to practice a new programming language, get help working on your personal projects, or try your hand at using the 3d printer. You might just come out to see what other folks are working on and lend a hand. If you know anyone who has been curious to come out to Knox Makers, please invite them along!
Like all other Tuesday nights, this event is free and open to the public. Our night will begin with a Show and Share where attendees are encouraged to bring out the projects they have been working on. This is a great time to request feedback for the future direction of your project, or you can just bring out something you want to show off. We hope to see you there!
Tuesday Night Talk: Hacking Pavotubes
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesHacking Pavotubes: An overview of how I reverse engineered the RF link to Pavotubes and designed and built a macro keyboard to control them.
Intro to soldering: Build a Blinky Kit
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesHave you wanted to learn to solder so you can do the occasional repair or kit build? Join us for a guided build of one of our custom Knox Makers solder kits and then take it home to earn geek street cred among your soon-to-be-jealous friends. In this class you will learn basic solder iron…
Intro to Metalworking (MIG 101)
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesThis is the Basic authorization class for using the Metalworking Shop and the MIG Welder. We will cover lots of safety and learn the metal shop tools. Expect an hour or so of hands-on setup and shared MIG welding time (more if needed.)The class may run a bit short or long depending on students' needs.
Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is OK but synthetic clothing or other materials that can melt are unsafe. Students can bring their own PPE (Personal Protective Equipment,) shield and gloves if they have them. but these are NOT required as we have setups for everyone to use.
Please do NOT bring your own welding machines to use, the setup and testing time could impact other students.
Open Hack Night – Public Welcome
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesOpen hack nights are a chance for people to come out to Knox Makers and hack on anything at any skill level. You can come out to practice a new programming language, get help working on your personal projects, or try your hand at using the 3d printer. You might just come out to see what other folks are working on and lend a hand. If you know anyone who has been curious to come out to Knox Makers, please invite them along!
Like all other Tuesday nights, this event is free and open to the public. Our night will begin with a Show and Share where attendees are encouraged to bring out the projects they have been working on. This is a great time to request feedback for the future direction of your project, or you can just bring out something you want to show off. We hope to see you there!
Power Hammer Authorization – LG25 “Thumper”
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the latest addition to the blacksmith shop, Thumper, Our 25lb Little Giant PowerHammer! This class will cover operational maintenance, necessary lubrication points, how to swap out dies, things to watch out for on this nearly 80 year old machine, and plenty of forging time to get comfortable with its capabilities.…
New Members Onboarding
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesWhether you’re a current member, trial member, or prospective member, you’re welcome to join us at this month’s New Member Onboarding!
We’ll start with a brief overview of Knox Makers’ origins and purpose and talk about how the organization works. You’ll learn a bit about the resources available to members and about the path to membership. Afterwards, we’ll hang out and socialize.
The focus is on new members, but longer-term members are encouraged to come and meet new folks.
Intro to surface mount soldering: Build a Serpinski triangle
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesBasic surface mount technology (SMT) soldering skills significantly broaden one's ability to do repair work, to miniaturize circuits, and to work with modern components that are not offered in through-hole formats. SMT soldering is often portrayed as difficult and intimidating but we have taught plenty of people to tackle this and virtually everyone finds it…
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will receive a key to access the forge and foundry building.
Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is OK but synthetic clothing or other materials that can melt are unsafe. We have eye protection available but suggest you bring your own if you have them.
This class is for members only and costs $11.96. There will be a 5 person maximum and a 2 person minimum. If the minimum isn’t met 24 hours in advance the class will be canceled.
Stitch n Bitch
Knox Makers - Fiber Arts 116 Childress St SW, Knoxville, TN, United StatesCome and hang out in Fiber Arts. Just bring a project to work on, hang out and have fun! Directions- Knox Makers parking and entrance is located around the back of the SPARK building in the fenced in area. Knox Makers is a place for the Knoxville area’s engineers, artists, hobbyists, innovators, educators and entrepreneurs…
Open Hack Night – Public Welcome
Knox Makers 116 Childress St SW, Knoxville, TN, United StatesOpen hack nights are a chance for people to come out to Knox Makers and hack on anything at any skill level. You can come out to practice a new programming language, get help working on your personal projects, or try your hand at using the 3d printer. You might just come out to see what other folks are working on and lend a hand. If you know anyone who has been curious to come out to Knox Makers, please invite them along!
Like all other Tuesday nights, this event is free and open to the public. Our night will begin with a Show and Share where attendees are encouraged to bring out the projects they have been working on. This is a great time to request feedback for the future direction of your project, or you can just bring out something you want to show off. We hope to see you there!