Skip to content
Loading Events

← Back to Events

Knox Makers – Machining

+ Google Map
116 Childress St SW
Knoxville, TN 37920 United States

March 2019

Milling 101 – Bridgeport Mill Tool Authorization

March 30, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Tony will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

Find out more »

April 2019

Machining 100 – Intro To Machining

April 25, 2019 @ 6:30 pm - 9:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**

Find out more »

Metal Turning 101 – Grizzly Lathe Tool Authorization

April 28, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

In this class you will receive basic hands on experience in operating a Grizzly G0602 10" x 22" Lathe. During this 3 to 4 hour class, Billy will go over the basics which include work holding, facing, center drilling, drilling, profile turning, grooving and parting operations. You will also learn the basics of using a dial indicator for more accurate parts, power feed, and basic care of the lathe. This is a tool authorization class and once completed you will be authorized to use the lathe and Knox Maker members will receive a key need to operate the lathe. Intro to Machining is a prerequisite class.

Find out more »

May 2019

Machining 100 – Intro To Machining

May 16, 2019 @ 6:30 pm - 9:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**

There will be a fee for this class of $9.96 for current Knox Makers members. There will be a maximum of 8 spots for this class, and a minimum of 3 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class will be canceled and all tickets will be refunded.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

May 18, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.95

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. *****

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

June 2019

Metal Turning 101 – Grizzly Lathe Tool Authorization

June 1, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Metal Turning 101 Class. **

In this class you will receive basic hands on experience in operating a Grizzly G0602 10" x 22" Lathe. During this 3 to 4 hour class, Billy will go over the basics which include work holding, facing, center drilling, drilling, profile turning, grooving and parting operations. You will also learn the basics of using a dial indicator for more accurate parts, power feed, and basic care of the lathe. This is a tool authorization class and once completed you will be authorized to use the lathe and Knox Maker members will receive a key need to operate the lathe. Intro to Machining is a prerequisite class.

(Not covered in the class: Threading, Boring Knurling, Spherical generation, or tapered turning between centers)

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

August 2019

Machining 100 – Intro To Machining

August 17, 2019 @ 1:00 pm - 3:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**
There will be a fee for this class of $9.96 for current Knox Makers members. There will be a maximum of 8 spots for this class, and a minimum of 3 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class will be canceled and all tickets will be refunded.

Find out more »

Project Lathe: Workday

August 17, 2019 @ 3:00 pm - 7:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States

Come help clean, tune and get the new 13x40 MSC lathe up and running. We purchased a new to us lathe which requires a little maintenance before it's ready to use. This is a good opportunity to see the insides of a lathe and learn a bit more about them.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

August 24, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. *****
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

September 2019

Machining 100 – Intro To Machining

September 26, 2019 @ 6:30 pm - 8:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**

Find out more »

October 2019

Machining 100 – Intro To Machining

October 24, 2019 @ 6:30 pm - 8:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw. **This is a prerequisite for the Bridgeport Mill and Lathe tool authorization classes**
There will be a fee for this class of $9.96 for current Knox Makers members. There will be a maximum of 8 spots for this class, and a minimum of 3 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class will be canceled and all tickets will be refunded.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

October 26, 2019 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

February 2020

Metal Turning 101 – MSC Lathe Tool Authorization

February 29, 2020 @ 3:00 pm - 7:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Metal Turning 101 Class. **

In this class you will receive basic hands on experience in operating a MSC 13" x 40" Lathe. During this 3 to 4 hour class, Billy will go over the basics which include work holding, facing, center drilling, drilling, profile turning, grooving and parting operations. You will also learn the basics of using a dial indicator for more accurate parts, power feed, and basic care of the lathe. This is a tool authorization class and once completed you will be authorized to use the lathe and Knox Maker members will receive a key need to operate the lathe. Intro to Machining is a prerequisite class.

(Not covered in the class: Threading, Boring Knurling, Spherical generation, or tapered turning between centers)

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

September 2020

Milling 101 – Bridgeport Mill Tool Authorization

September 5, 2020 @ 1:00 pm - 7:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
Free – $24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

November 2020

Machining 100 – Intro To Machining

November 19, 2020 @ 6:30 pm - 8:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

May 2021

Machining 100 – Intro To Machining

May 27 @ 7:00 pm - 9:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

May 29 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

July 2021

Machining 100 – Intro To Machining

July 15 @ 6:30 pm - 9:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

July 24 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

August 2021

Machining 100 – Intro To Machining

August 19 @ 6:30 pm - 9:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

August 21 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

Metal Turning 101 – MSC Lathe Tool Authorization

August 22 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Metal Turning 101 Class. **

In this class you will receive basic hands on experience in operating a MSC 13" x 40" Lathe. During this 3 to 4 hour class, Billy will go over the basics which include work holding, facing, center drilling, drilling, profile turning, grooving and parting operations. You will also learn the basics of using a dial indicator for more accurate parts, power feed, and basic care of the lathe. This is a tool authorization class and once completed you will be authorized to use the lathe and Knox Maker members will receive a key need to operate the lathe. Intro to Machining is a prerequisite class.

(Not covered in the class: Threading, Boring Knurling, Spherical generation, or tapered turning between centers)

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

October 2021

Machining 100 – Intro To Machining

October 21 @ 6:30 pm - 9:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

October 23 @ 1:00 pm - 5:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

Milling 201 – Advanced Bridgeport Mill Tool Authorization

October 28 @ 6:30 pm - 9:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

This is an accelerated class designed to get you checked out on the Bridgeport Series I J-Head milling machine. This is a faster paced class than the Milling 101 Auth class and assumes you've had some experience milling with a Bridgeport or Bridgeport type machine. Like the Milling 101 class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »

November 2021

Machining 100 – Intro To Machining

November 24 @ 6:30 pm - 9:30 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$9.96

Billy will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.

Find out more »

Milling 101 – Bridgeport Mill Tool Authorization

November 27 @ 3:00 pm - 7:00 pm
Knox Makers – Machining, 116 Childress St SW
Knoxville, TN 37920 United States
$24.96

** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **

In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.

There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 2 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.

Find out more »
+ Export Events
Scroll To Top