Machining 100 – Intro To Machining
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United StatesBilly will give you a basic introduction to the machining area. This class will begin with a tour of the machining area with a, in-depth discussion of each tool, it’s uses, proper procedures, and safety. At the end of this class, all participating members will be authorized to use the drill press, box pan brake, handtools, and the horizontal bandsaw.
Milling 101 – Bridgeport Mill Tool Authorization
Knox Makers - Machining 116 Childress St SW, Knoxville, TN, United States** Intro to Machining is a prerequisite class. You have to complete the Intro to Machining class before you can take the Milling 101 Class. **
In this class you will receive basic hands on experience in operating a Bridgeport Series I J-Head milling machine. During this 3 to 4 hour class, Billy will go over the basics of tramming the head of the mill, tramming the vise, edge finding, work holding and setup, drilling , side milling, and top/end milling operations. You will also learn the basics of the DRO (digital read out), the table power feed, and basic care of the mill. This is a tool authorization class and once completed you will be authorized to use the milling machine and Knox Maker members will receive a key need to operate the mill. Intro to Machining is a prerequisite class.
There will be a fee of $24.96 for members.. There will be a maximum of 4 spots of this class, and a minimum of 1 tickets must be sold. If the class minimum is not met 48 hours prior to class start time, the class we be canceled and all tickets will be refunded.
Arduino 101 – Chapter 4
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesArduino 101 – Chapters 4 to 8
For those who have finished Arduino 101 and want to continue with the in person classes at Knox Makers, you can sign up for the remaining classes for $14.96 for Knox Makers members and $19.96 for the general public. All of the proceeds from this class, above the cost of the kits, will go to the Knox Makers Electronics area. This class is a bargain, so if you want to also donate to Knox Makers and designate the electronics section for the gift, that would be great. These 4 classes will continue on Mondays from 6:00 pm to 7:30 pm on the following dates (note we skip Halloween):
November 7: Chapter 4
November 14: Chapter 5
November 21: Chapter 6
November 28: Chapter 7
December 5: Chapter 8
Intro to TIG Welding (TIG Welding 201)
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesThis is the next class in the welding series granting authorization on the TIG Welders and Hand Plasma Cutter. You MUST have completed Introduction to Metalworking (MIG 101) or already be a non-novice welder before taking this class. This is not an intro to the metal shop, but the next step focusing on beginning TIG.…
New Members Onboarding
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesWhether you’re a current member, trial member, or prospective member, you’re welcome to join us at this month’s New Member Onboarding!
We’ll start with a brief overview of Knox Makers’ origins and purpose and talk about how the organization works. You’ll learn a bit about the resources available to members and about the path to membership. Afterwards, we’ll hang out and socialize.
The focus is on new members, but longer-term members are encouraged to come and meet new folks.
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will receive a key to access the forge and foundry building.
Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is OK but synthetic clothing or other materials that can melt are unsafe. We have eye protection available but suggest you bring your own if you have them.
Scrap Metal Art
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesLearn to make metal sculptures from recycled metal scrap!
No experience necessary- just use your imagination.
We will begin by covering shop safety and go over some tool basics. After a bit of discussion about scrap materials the class will design and create their own small sculptures to take home.
Power Hammer Authorization – LG25 “Thumper”
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the latest addition to the blacksmith shop, Thumper, Our 25lb Little Giant PowerHammer! This class will cover operational maintenance, necessary lubrication points, how to swap out dies, things to watch out for on this nearly 80 year old machine, and plenty of forging time to get comfortable with its capabilities.…
Let’s Sew Some Covers for Metal Working
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesCome help sew up some covers for the new welding machines. We’re getting creative by sewing up some fabric swatches into 8’ by 3’ covers. No rules, no fussy matching, just straight seams. Perfect for the beginner to practice straight stitching or the creative at heart for the layout. We have all the tools and materials just bring a positive attitude.
Woodworking 101
Knox Makers - Woodworking 116 Childress St SW, Knoxville, TN, United StatesThis class will cover topics related to safe and correct operation of equipment within the woodworking area, as well as some shop etiquette guidelines. This is the authorization class for the area and is required prior to using the equipment. Safe practices will be demonstrated and learned by a hands on approach in the context…
Virtual Board Meeting
Knox Makers - VirtualKnox Makers members are welcome to join us as we hold our monthly board meeting. The board will be discussing pertinent topics happening around the space. All current, paying Knox Makers members are welcome to attend. This event is closed to the general public. Directions: This is a virtual event. Check Mattermost for further details…
Arduino 101 – Chapter 5
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesArduino 101 – Chapters 4 to 8
For those who have finished Arduino 101 and want to continue with the in person classes at Knox Makers, you can sign up for the remaining classes for $14.96 for Knox Makers members and $19.96 for the general public. All of the proceeds from this class, above the cost of the kits, will go to the Knox Makers Electronics area. This class is a bargain, so if you want to also donate to Knox Makers and designate the electronics section for the gift, that would be great. These 4 classes will continue on Mondays from 6:00 pm to 7:30 pm on the following dates (note we skip Halloween):
November 7: Chapter 4
November 14: Chapter 5
November 21: Chapter 6
November 28: Chapter 7
December 5: Chapter 8
Intro to Cutting Torch (Cutting Torch 101)
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis is the Authorization Class to use the oxy-fuel cutting torch.
We will spend some time going over safety and then move on to operation of a cutting torch. We will cut out some basic shapes as well as learn some other tricks you can use a torch for.
Students should wear natural fiber clothing (jeans, cotton shirts, etc) NO polyester, spandex or "tech" style clothes. Socks and shoes are required, NO sandals or open toes.
If you have own PPE- please bring safety glasses, leather gauntlets, shade 5 cutting goggles/glasses, and a welding shirt/jacket. *If you do not have this yourself do not worry! We will have gear for you to use!*
Blacksmithing Authorization – Intro to Forging
Knox Makers - Blacksmithing 116 Childress St SW, Knoxville, TN, United StatesThis class introduces you to the new blacksmithing zone. We cover propane forge operation, zone safety, basic hand forging, and nail making. At the completion of the class, members will receive a key to access the forge and foundry building. Proper attire is natural fiber clothing such as cotton jeans and T-shirts. Cotton/polyester blend is…
Mortise and Tenon Joinery
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesFitting a square hole and corresponding square peg together is a convenient mechanical joint for a variety of assemblies. In this class I will demonstrate a variety of techniques which can be used to accomplish this task and create well-fitting and functional mortise and tenon joinery. Topics covered will include; anatomy of the joint, rationale for layout and proportions, hand-cut mortising (techniques and tools), machine-cut mortising, hand-cut tenons, machine cut tenons (with and without jigs), dowel riving and drawbore pinning. Terms you will understand by the end of class include, haunch, drawbore, wedged, dual tenon, and riven. Tools used will include mortising gauge, marking gauge, scribe, joinery mallet, carcass saw, tenon saw, router plane, rebate/rabbit plane, bench chisels, mortising chisels (English and Western), dowel plate, square mortising machine, table saw, dado stack, and tenoning jig.
The cost is $24.96 for Knox Makers members, $49.96 for General Public
Laser Cutting Authorization
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesThis is an introduction class to our laser cutter, Moonraker. Tracy will lead attendees of this class as they learn the basics of laser cutting, make a simple design, and then engrave and cut out the design using the laser cutter in our space. This class is intended for members who have not yet been…
Metal Shop Mingle
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesCalling all past, current, and future metalworkers to come hang out and talk shop! Come get help with your current projects! Come talk about your future projects! Let's burn some wire and throw some sparks! This is a time when you can seek help with any projects you might have, come ask questions, seek help…
Arduino 101 – Chapter 6
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesArduino 101 – Chapters 4 to 8
For those who have finished Arduino 101 and want to continue with the in person classes at Knox Makers, you can sign up for the remaining classes for $14.96 for Knox Makers members and $19.96 for the general public. All of the proceeds from this class, above the cost of the kits, will go to the Knox Makers Electronics area. This class is a bargain, so if you want to also donate to Knox Makers and designate the electronics section for the gift, that would be great. These 4 classes will continue on Mondays from 6:00 pm to 7:30 pm on the following dates (note we skip Halloween):
November 7: Chapter 4
November 14: Chapter 5
November 21: Chapter 6
November 28: Chapter 7
December 5: Chapter 8
MIG Welding 101
Knox Makers - Metalworking 116 Childress St SW, Knoxville, TN, United StatesThis is the Basic authorization class for using the Metalworking Shop and the MIG Welder. We will cover lots of safety and learn the metal shop tools. Expect an hour or so of hands-on setup and shared MIG welding time (more if needed.)The class may run a bit short or long depending on students' needs.…
Arduino 101 – Chapter 7
Knox Makers - Classroom 116 Childress St SW, Knoxville, TN, United StatesArduino 101 – Chapters 4 to 8
For those who have finished Arduino 101 and want to continue with the in person classes at Knox Makers, you can sign up for the remaining classes for $14.96 for Knox Makers members and $19.96 for the general public. All of the proceeds from this class, above the cost of the kits, will go to the Knox Makers Electronics area. This class is a bargain, so if you want to also donate to Knox Makers and designate the electronics section for the gift, that would be great. These 4 classes will continue on Mondays from 6:00 pm to 7:30 pm on the following dates (note we skip Halloween):
November 7: Chapter 4
November 14: Chapter 5
November 21: Chapter 6
November 28: Chapter 7
December 5: Chapter 8